

When it comes to vehicle maintenance, we have to mention going out for rescue, especially commercial diesel vehicles. They often work at full load, and vehicle failure is inevitable. Today, we received a rescue request, and the masters went to have a look.
Diesel Engine
Diesel Engine
Diesel Engine
A Guosi Haowo cement tank car cannot be started. Our office asked what is the electric control system? With or without Mini controller? The answer is unclear. Since the heavy truck engine is equipped with Bosch and electric installation two common rail systems respectively, the start control modes include engine computer direct control start and can line start with min controller. Prepare for complex can line start, and go to the rescue after the circuit diagram, computer and body controller are fully prepared
On site observation shows that the vehicle is equipped with Bosch common rail, edc17cv44 computer, and the urea system is the second generation of independent gas drive of heavy truck.
The body computer is nano BCU, which is started by non can line control.
Verify the fault. Start the motor with the ignition switch and it cannot be put into operation immediately. The motor starts to rotate only after the key is kept in the starting gear for 5S, so as to drive the engine to run by itself. After landing, the vehicle runs normally. According to the reaction fault phenomenon, it obviously belongs to the “emergency start” mode when the computer cannot receive the neutral switch signal. The problem is very simple. The neutral position signal required by the engine computer can be maintained.
The upper decoder reads the fault code. There is only 12V power supply fault. Generally, it is the power supply of vehicle speed sensor, which has no impact on startup. Enter the data flow and observe the neutral position signal. The display is not activated. Move the gear repeatedly, and the data does not change. Unplug the harness plug of neutral switch for short circuit, and the data remains unchanged. The multimeter detects the voltage, and there is no voltage or grounding on both wires. Query the pin diagram of heavy truck edc17cv44 computer. K67 is the neutral switch signal line. The computer outputs 24V signal voltage. When it is in the neutral position, this line is grounded. When the computer receives no voltage, it is determined as neutral. If there is a start signal from the key, i.e. K35 calls, it is allowed to turn on the starter relay to start the vehicle. On the contrary, if there is 24V voltage, the computer
determines that there is gear, and it is not allowed to start the relay to ensure safety. The voltage on the neutral switch harness socket is not measured. It should be that the signal line is disconnected. Measure it directly from the computer and break the k67 line to measure 24V voltage.
Ground this line directly, observe that the neutral position of the data flow still shows inactive, and the repeated grounding and disconnection do not change. The adjacent auxiliary brake signal data shows active and inactive synchronously, and the relay synchronous working sound also comes from the instrument panel. It turns out that it is the auxiliary brake signal line, and the pins in the circuit diagram are inconsistent.
Continue to search. The drawing obtained is the same as the circuit diagram used earlier. Will it be a general-purpose, neutral switch controlled live wire? I decided to try. The signal line of the pin neutral switch of the general-purpose computer is K19. There is no voltage or short circuit to ground measured. I directly input 24V power supply. The neutral signal on the data stream still shows that it is not activated, and it is not a general-purpose fire control mode. There are two other ways:
1. Connect an ordinary 5W bulb test lamp in series, power on and ground the input switch signal one by one, and observe the neutral signal data flow. If it changes synchronously, it will be the neutral signal line, which is time-consuming and laborious.
2. Seek the original circuit diagram of SINOTRUK and obtain the pin definition of neutral signal, which shall be accurate.
Two pronged approach, check the diagram while testing, and soon test that K14 is a neutral signal line. The space-time signal display of power supply is activated, and it is not activated if power supply is not provided. After the voltage of this line is increased, the test is started. When the key is turned to the start gear, the motor runs immediately, the engine starts immediately, the vehicle returns to normal, and the fault is eliminated.
Fault summary: the neutral switch signal of the vehicle is K14. It is neutral when there is 24V high voltage, and it is in gear when there is no voltage. After that, we found the original circuit diagram, and the pins shown were consistent with the real car, which was sorted and hand drawn as the following figure.
The signal of simple neutral switch is missing, and the vehicle starts in an emergency way, but it makes a big turn due to inaccurate data.
Emergency start:
The computer outputs the neutral switch signal line to the neutral switch, and K68 outputs 24V power supply to the neutral switch. When the transmission is in neutral, the switch is connected, K14 obtains high voltage, the computer confirms that it is in neutral, and it is allowed to start, otherwise it is in gear, and it is not allowed to start the vehicle directly. When the neutral switch signal line is open circuit and the neutral signal is not received, the key can be kept in the starting gear for a certain time (about 5 seconds), The engine can be started in an emergency.
Case editor: Jingyi diesel EFI
SITRAK, HOWO, HOHAN, STEYR, WANGPAI, FOLOR, and becomes China’s truck manufacturer with the most complete drive types and power range in heavy-duty truck industry.